In the above example it stops at 12.2 m (40.0 ft). The deepstop calculation keeps running for another 1.5 m (4.9 ft) up but stops after that. If the diver keeps ascending, after 0.5 m (1.6 ft), a downward pointing red arrow and an alarm notify the diver to descend immediately. The deepstop target depth number also turns yellow. When the diver ascends above the deepstop window ceiling - in this case above 14.2 m (46.5 ft) - a downward pointing yellow arrow signals that the depth is not optimal, it is recommended to descend. The deepstop window is +/- 1.5 m (4.9 ft) and when the diver is within the deepstop window, it is indicated with two white arrows pointing at each other on the display. If the deepstop depth is 15.2 m (49.8 ft), the calculation starts at 15.7 m (51.5 ft) and stops at 12.2 m (40.0 ft). In this case, as the diver ascends, the deepstop is necessary at halfway of the maximum depth, so at 15.2 m (49.8 ft). In the following example the diver dives down to maximum 30.4 m (99.7 ft) and has a deepstop at 15.2 m (49.8 ft):īelow 20.0 m (66 ft), deepstop gets activated. For example, if you dive to 42 m (137.8 ft), the first deepstop is prompted at 21 m (68.9 ft) and the second is at 10.5 m (34.4 ft) The second deepstop is 2 minutes long. There can be more than one deepstop during ascend. Keep track of time for all your project in one place and then post it. Easy to use Time Tracking for the Mac featuring a clean intuitive interface. Eon can not only track the time, but it synchronizes with over 40 different online services. Calculation ends - 3 m (- 9.8 ft) away from deepstop depth. Keeping track of time that you spend on a project is the basis of every business. Calculation starts at deepstop target depth plus 0.5 m (1.6 ft). The deepstop window is +/- 1.5 m (4.9 ft). You are in the deepstop area when the deepstop depth has up/down arrows in front of it and deepstop time is running. ![]() Deepstops are presented like safety stops. During ascend, deepstops activate when you are halfway up from your maximum depth. Voluntary safety stop is shown in yellow:ĭeepstops activate only when you dive deeper than 20 m (66 ft). Safety stops can be set to three (3), four (4), or five (5) minutes. If violations happened several times, the additional stop time is longer. The time may exceed three (3) minutes if you ascend too fast during dive. The safety stop time is shown in minutes and seconds. This is presented with up/down arrows on the left side of the stop depth value. The time for a safety stop is calculated when you are between 2.4 and 6 m (7.9 and 19.6 ft). ![]() Mandatory safety stop is shown in red, while voluntary safety stop is indicated with yellow.Ī three (3) minute safety stop is always recommended for every dive over 10 meters (33 ft). Safety stop is mandatory if ascent speed violation happened during the dive. There are two types of safety stops: voluntary and mandatory. Leave the lag spot blank for now, check GBA box if youre using a GBA/SP. For the frames you enter the target frame you want (example if you want the spread from frame 100000 you enter 100000 into there). Safety stop and deepstop times are counted down in minutes and seconds. Basically you SR when the first timer runs out (personally I just set the first timer to 0 and SR and start the timer at the same time). We support your favorite online services via in-app purchases to easily update your time to including (each service integration is $4.99, or you can purchase an all-integrations pack for $14.Safety stop and deepstop ceilings are always at constant depth when you are at the stop. Keep track of time for all your project in one place and then post it to your online service, if you wish so.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |